Ciao! I'm davide from italy (sorry for the grammar),and i'm trying to activate the webcam Z-Star with the "Jef Moine" driver: gspcav2-2.0.3 <http://moinejf.free.fr/gspcav2-2.0.3.tar.gz>
on the website it seems to work..
The drivers compilation and installation goes well,
the modules loading too,
but the webcam seems doesn't work :-(
I did as advised Jef:
1) - do
echo 0x3f > /sys/module/gspca_main/parameters/debug
2) then start the application, and send me the last kernel
messages:
usb 2-1: USB disconnect, address 2
gspca: kill transfer
gspca: disconnect complete
usb 2-1: new full speed USB device using uhci_hcd and address 4
usb 2-1: configuration #1 chosen from 1 choice
gspca: probing 0ac8:307b
zc3xx: probe 2wr ov vga 0x0000
zc3xx: probe 3wr vga 1 0x4001
zc3xx: probe 3wr vga type 29
zc3xx: probe sensor -> 29
zc3xx: Find Sensor GC0305
gspca: probe ok
usb 2-1: New USB device found, idVendor=0ac8, idProduct=307b
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: PC Camera
usb 2-1: Manufacturer: Vimicro Corp.
gspca: hald-probe-vide open
gspca: open done
gspca: querycap
gspca: querycap
gspca: enum fmt cap
gspca: try fmt cap JPEG 10000x10000
gspca: hald-probe-vide close
gspca: close done
type=1400 audit(1214479558.547:132): avc: denied { syslog_read } for
pid=2975 comm="dmesg"
scontext=unconfined_u:system_r:hotplug_t:s0-s0:c0.c1023
tcontext=system_u:system_r:kernel_t:s0 tclass=system
gspca: disconnect complete usb 2-1: new full speed USB device using uhci_hcd and address 5 usb 2-1: configuration #1 chosen from 1 choice gspca: probing 0ac8:307b zc3xx: probe 2wr ov vga 0x0000 zc3xx: probe 3wr vga 1 0x4001 zc3xx: probe 3wr vga type 29 zc3xx: probe sensor -> 29 zc3xx: Find Sensor GC0305 gspca: probe ok usb 2-1: New USB device found, idVendor=0ac8, idProduct=307b usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 usb 2-1: Product: PC Camera usb 2-1: Manufacturer: Vimicro Corp. gspca: hald-probe-vide open gspca: open done gspca: querycap gspca: querycap gspca: enum fmt cap gspca: try fmt cap JPEG 10000x10000 gspca: hald-probe-vide close gspca: close done and the run "./grab": http://www.cosmogonia.org/cosmogoniA/tmp/toto.jpg and dmesg: gspca: grab open gspca: open done gspca: querycap gspca: set fmt cap JPEG 640x480 gspca: try fmt cap JPEG 640x480 gspca: reqbufs 4 gspca: frame alloc frsz: 307200 gspca: new fr_sz: 94208 gspca: reqbufs st:0 c:4 gspca: querybuf gspca: mmap start:b80e7000 size:94208 gspca: querybuf gspca: mmap start:b80c9000 size:94208 gspca: querybuf gspca: mmap start:b80b2000 size:94208 gspca: querybuf gspca: mmap start:b809b000 size:94208 gspca: stream on gspca: init transfer alt 7 gspca: use ISOC alt 6 ep 0x81 gspca: isoc 32 pkts size 768 (bsize:24576) zc3xx: gamma:4 contrast:128 gamma coeff: 0/128 zc3xx: tb: 13 38 59 79 92 a7 b9 c8 zc3xx: d4 df e7 ee f4 f9 fc ff zc3xx: 26 22 20 1c 16 13 10 0d zc3xx: 0b 09 07 06 05 04 03 02 gspca: stream on OK JPEG 640x480 gspca: stream off gspca: kill transfer gspca: stream off OK gspca: grab close gspca: frame free gspca: close done could yu give me any suggestion? :-) thanks a lot!! -- cosmogoniA <http://www.cosmogonia.org/> noprovarenofareononfarenonc'èprovare
Attachment:
smime.p7s
Description: S/MIME Cryptographic Signature
------------------------------------------------------------------------- Check out the new SourceForge.net Marketplace. It's the best place to buy or sell services for just about anything Open Source. http://sourceforge.net/services/buy/index.php
_______________________________________________ Spca50x-devs mailing list Spca50x-devs@xxxxxxxxxxxxxxxxxxxxx https://lists.sourceforge.net/lists/listinfo/spca50x-devs